Website

 

In this article below you'll find lots of excellent content with regards to Installing A Bathtub.

Installing a bath tub isn't precisely brain surgery, however it does need solid plumbing, woodworking, and also often, tiling skills. Changing an old bath tub with a new one is likewise a reasonably challenging job. If the old bathtub is conveniently easily accessible, the task can move immediately; if you have to open up a wall surface to get rid of the old bathtub and place the new tub, the task is a lot harder. In either situation, the project is within a house handyman's skills, although you will require a helper to move out the old bathtub as well as embeded in the new one. See to it you have actually qualified yourself for the task and fit attempting it. As opposed to employing a specialist to take control of a halfway-completed task, it is far better to take into consideration utilizing one prior to you begin. Opportunities are you may require a specialist plumber to make tube links.
This post will assist you mount a brand-new tub in your bathroom if you have currently gotten a brand-new bathtub as well as do not require to change the arrangement of your previous water system pipes.
Your tools and product list need to comprise the following:

 

• New Tub


• Hammer


• Pipe Wrenches


• Prybar


• Safety Glasses


• Degree


• Pliers


• Adjustable Wrench


• Putty Blade


• Screwdriver


• Cold Blade


• Measuring tape


• Pipe Caps


 

Preparing for the Installment

To start with, the sustaining framework provided with the bath should be fitted (if called for) according to the supplier's guidelines. Next, fit the faucets or mixer to the bath tub. When suitable the tap block, it is necessary to ensure that if the tap includes a plastic washer, it is fitted in between the bath as well as the faucets. On a plastic bath, it is also practical to fit a supporting plate under the faucets device to stop pressure on the bath tub.
Fit the flexible faucet adapters to the bottom of both taps utilizing 2 nuts and also olives (occasionally supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and then pass the outlet through the hole in the bathroom. Make use of the nut supplied by the manufacturer to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the versatile overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bath. Make sure you use all of the supplied washers.
Link the trap to the bottom of the waste outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Connect all-time low of the overflow tube in a comparable manner.The bath must now prepare to be suited its last placement.

 

 

Removing Old Touches

If you require to change old faucets with brand-new ones as a part of your installment, after that the first thing you need to do is disconnect the water system. After doing so, switch on the taps to drain any kind of water remaining in the system. The process of getting rid of the existing taps can be rather bothersome because of the restricted access that is typically the case.
Utilize a basin wrench (crowsfoot spanner) or a faucet tool to undo the nut that attaches the supply pipelines to the faucets. Have a fabric prepared for the remaining water that will come from the pipes. Once the supply pipes have been gotten rid of, use the same tool to loosen up the nut that holds the faucets onto the bath/basin. You will need to quit the single faucets from transforming throughout this process. As soon as the faucets have been eliminated, the holes in the bath/basin will have to be cleaned of any old securing substance.
Prior to going on to fit the brand-new faucets, contrast the pipeline links on the old taps to the brand-new faucets. If the old taps are longer than the new taps, after that a shank adapter is required for the new taps to fit.

 

 

Mounting the Bathtub

Utilizing the two wooden boards under its feet, position the bath tub in the needed position. The wood boards are practical in equally spreading the weight of the bathtub over the location of the boards rather than focusing all the weight onto 4 small factors.
The following goal is to make sure that the bath tub is leveled all round. This can be achieved by examining the spirit level and also adjusting the feet on the tub until the spirit level reviews level.
To install taps, fit the bottom of the furthest flexible faucet adapter to the proper supply pipeline by making a compression join; then do the very same for the various other tap.
Switch on the supply of water and check all joints and new pipework for leakages as well as tighten them if necessary. Fill up the tub and likewise check the overflow electrical outlet and the normal outlet for leaks.
Lastly, take care of the bathroom paneling as explained in the maker's instruction manual. Tiling and also securing around the bathtub must wait until the bathtub has been utilized at least when as this will certainly settle it into its last position.

 

 

Fitting New Touches

If the tails of the new taps are plastic, after that you will certainly require a plastic port to prevent damage to the string. One end of the adapter fits on the plastic tail of the faucet as well as the various other end offers a link to the current supply pipes.
If you need to fit a monobloc, then you will require decreasing couplers, which attaches the 10mm pipeline of the monobloc to the common 15mm supply pipe.
Next, position the faucet in the installing opening in the bath/basin making certain that the washers are in location in between the tap as well as the sink. Protect the faucet in position with the maker given backnut. Once the faucet is safely in position, the supply pipelines can be connected to the tails of the taps. The faucets can either be attached by utilizing corrugated copper piping or with typical tap connectors. The former kind must be linked to the faucet ends initially, tightening just by hand. The supply pipelines can later on be connected to the other end. Tighten up both ends with a spanner after both ends have been attached.

 

 

Tiling Around the Tub

In the location where the bathroom satisfies the ceramic tile, it is essential to secure the accompanies a silicone rubber caulking. This is essential as the installation can relocate sufficient to fracture a rigid seal, triggering the water to permeate the wall surface between the bathroom and the tiling, bring about complications with wetness as well as feasible leakages to the ceiling listed below.
You can choose from a range of coloured sealers to assimilate your components and also installations. They are offered in tubes and cartridges, and are capable of sealing voids approximately a size of 3mm (1/8 inch). If you have a larger gap to fill up, you can fill it with spins of drenched paper or soft rope. Keep in mind to always load the bathtub with water prior to sealing, to enable the movement experienced when the tub remains in use. The sealant can crack fairly early if you do not consider this movement before securing.
Alternatively, ceramic coving or quadrant floor tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are additionally easily offered on the market. It is a good idea to fit the ceramic tiles using waterproof or water resistant glue and cement.

 

How to Install or Replace a Bathtub

 

Find Your Dimensions

 

The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.

After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?

 

Disconnect the Water Supply and Drain Assembly

 

Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.

Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.

Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.

 

Cut Out the Old Tub

 

After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.

Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.

Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.

 

Install the New Tub

 

Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.

Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.

Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.

When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.

 

Secure the Tub

 

After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.

Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.

Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.

Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/

 

Hopefully you enjoyed our piece about A Step-by-Step Guide to Installing a Bathtub. Thanks a lot for finding the time to read our content. Are you aware of another person who is looking into the niche? Please feel free to share it. I cherish reading our article about Tools You Need to Install a New Bathtub .

Call now!